Motorcycle enthusiasts love their bikes because they provide a unique sense of freedom and independence from other vehicles. They also understand the importance of keeping their rides looking new and using detailing products.
When performing a detail job on a motorcycle, you must have the following products in your arsenal. Visit https://www.perthdetailer.com.au/ to learn more.
Motorcycle detailing is a lot more work than simply washing your car, but with the right tools, techniques and dedication, it can be a fun and rewarding process. Whether you’re getting your bike ready for a bike night or want to draw top dollar when it comes time to sell, the proper cleaning process is vital.
Just like any other vehicle, a thorough and consistent detail is essential to keeping your motorcycle looking brand new for years to come. It helps to increase its lifespan, extend its resale value and even ensures the safety of you and your passenger when riding.
Before starting any cleaning, make sure the engine and pipes are cool. If they are too hot, the sudden change in temperature can damage them permanently. You should also take this opportunity to perform a visual inspection of your motorcycle to look for any areas that may need attention or repair, such as corrosion on the frame or exposed electrical connections.
Next, use a garden hose to rinse the entire motorcycle thoroughly. Start at the top and work your way down, paying special attention to removing any large dirt or debris that may have accumulated in hard-to-reach places, such as between the wheels. This will prepare the motorcycle for the washing stage, which should be done using a quality soap and water.
Liquid cleaners can help to shorten the duration of this step by quickly dissolving tar, oil and other sticky residues. These products should be applied to the affected area using a sponge or cloth and allowed to sit for a few minutes before being rinsed off with clean water.
When washing your motorcycle, be sure to use a good quality soap and water to prevent damaging its paint finish. The key to a successful wash is patience and precision. Scrub the entire surface of the motorcycle using a soft sponge or wash mitt, taking care to pay special attention to any nooks and crannies where grime can hide. Rinse well and repeat as necessary to remove all soap residue.
After washing, dry the motorcycle with a microfiber towel or air blaster. Pro detailers prefer the latter because it blows warm, dry filtered air that drives away water from all surfaces of the motorcycle, including the small crevices on which dirt can cling.
For a bike to look its best, it needs to be clean. Detailing a motorcycle can be challenging, but for those with patience and a keen eye for detail, it can be a deeply satisfying experience. Properly detailing your motorcycle can boost its resale value, extend its lifespan and keep it looking new for years to come.
Before starting the cleaning process, make sure your motorcycle is in neutral and that the engine is cool to prevent damage to it and other components. It is also a good idea to plug or cover any electrical components that may be exposed to water so they stay dry. It is also recommended to remove the seat, trunk, bags and windshield for easier access and to avoid scuffing or scratching them.
After prepping the motorcycle, start the cleaning process with a high-quality degreaser that is safe for use on a motorbike. Apply the degreaser to the bike with a soft cloth or sponge and scrub away any dirt, grime and built-up grease. Be careful when scrubbing, as some parts of the bike, like the exhaust or the battery, are hot and can easily be damaged by contact with water.
Using the proper cleaning products will ensure that the paintwork stays intact and is free of contaminants and blemishes. Never use household or laundry detergents or chemicals on a motorcycle, as they can damage the finish and even the metal components. Instead, find a professional motorcycle cleaner that is safe to use on your bike’s paintwork.
Once the bike is cleaned, it is a good idea to use a clay bar to smooth out the surface and remove any contaminants that are trapped in the paint. Then, rinse the motorcycle thoroughly to get rid of all the soap and debris. After rinsing, it is important to dry the motorcycle completely to avoid water spots and streaks. A quality microfiber drying towel is perfect for this.
Then, use a wax or sealant to protect the paint and chrome surfaces and a non-slick protectant on the leather seats. It is also a good idea to use a leaf blower or similar tool to push out any remaining water from the nooks and crannies of the bike.
Whether or not you polish the chrome on your motorcycle is a matter of preference. It may depend on how much use the bike gets and what type of polish you use to remove the oxidation. A light abrasive that can be used as a metal polish and wax can quickly remove oxidation from metal surfaces while adding shine and protecting the surface of the metal. If you do decide to polish the chrome on your motorcycle, it is important to use a shaded area and a non-humid environment. This will prevent water spots from forming on the chrome as it is being polished.
The next part of the detailing process involves cleaning any scuff marks or dirt that may have been left on the wheels and tires after riding. Wash the wheels and tires using a mild degreaser that will not damage or dry out your paint.
If your pride and joy has an oil tank, be sure to clean the entire exterior of the tank and access points thoroughly with soapy water. The same applies to the engine and other components. It may require a bit of elbow grease and some scrubbing, but a clean engine will run better and longer than an overdue one. Professional detailers often recommend the use of an engine brightener to restore the appearance of the engine and help protect it from further deterioration.
Leather can be difficult to clean, and you will want to ensure that you are using the right type of cleaner for your specific upholstery. Different leathers need to be cleaned in a specific way, so check the owner’s manual for tips that are specific to your particular material.
Once the wheels and tires are washed, a good rubbing compound will help restore and protect them. A high quality tire and wheel polish will also make your motorcycle look great while providing protection that will last for years.
Another aspect of motorcycle detailing is the polishing of the metal surfaces, such as the frame and the exhaust. Mercury Metal Polish is a great product for this, as it has an extremely light abrasive that can be applied in small sections and quickly restore a new shine to metal surfaces without stripping away the underlying layer of metal.
A quality wax provides a high-gloss finish and protects the paint from moisture, dirt and UV radiation. You can use a spray on wax such as Turtle Wax Ice which only takes minutes to apply. Just lightly mist a small section of your bike at a time and rub in circular motions with a clean microfiber towel to get a shiny finish. It’s safe to use on metal, plastic and glass. This step is important to help your hard work last as long as possible.
When washing your bike, make sure to rinse often and use a gentle stream of water. You also want to rinse off your tools, rags and buckets regularly as well. Doing this will keep your soap from drying on the surface of the bike and leave unsightly streaks and spots.
If your motorcycle has a chrome or uncoated aluminum frame, it’s important to polish these parts with a fine metal polish. The light abrasive action of the polish quickly removes oxidation and will help your bike look like new.
Many professional detailers recommend using engine brightener on your motorcycle as it can remove grime that has been baked onto the engine by the sun and heat. A quality product will also contain UV inhibitors to prevent the engine from discoloring over time.
While it may not be necessary to use on a regular basis, many motorcycle owners like to keep a can of degreaser in the garage for those big jobs that require a lot of elbow grease and a fair amount of time to complete. This will help loosen up stuck on grit and dirt to prevent it from scratching your expensive paint job.
Once the paint and chrome have been polished and waxed it’s a good idea to apply a sealant or a protectant to non-painted surfaces such as the rubber, wires and black plastic. A high-quality product will keep the hard work you’ve put into your bike protected and will give you a better ride over time.